Protek 6510 Analog Oscilloscope 100MHz

Features: • Four traces may be simultaneously displayed in ALT-sweep • Five vertical display modes: CH1, CH2, Dual, Add, Subtract • Vertical mode triggering for displaying 2 unrelated signals • Trigger hold-off circuit for synchronizing complex waveforms • Sweep speeds to 2nS/ Div • 12kV acceleration voltage for bright displays of low duty cycle signals • Z axis input • TV Synchronization for either line or field patterns • 20MHz bandwidth limit switch for triggering signals in a noisy environment Specifications Vertical Amplifier ( CH 1 and CH 2) Sensitivity: 5 mV/ Div to 5 V/ Div in 7 calibrated steps, ( X5 Mag 1mV/ Div to 1 V/ Div) Accuracy: ± 3% ( ± 5% in X5 Mag) Bandwidth ( -3dB) : DC to 100MHz Rise Time: £ 3.5 ns, X5 Mag: 20MHz Bandwidth: £ 17 ns Input Impedance: 1MW + 25 pF Input Coupling: AC-Gnd-DC Invert Channel: CH2 Display Modes: CH1, CH2, Add, Subtract, Dual ( Alt/ Chop) Maximum Input Voltage: 400V ( DC or AC peak) CH1 Signal Output: 20mV into 50W Horizontal Sweep • Timebase A - Sweep Time: 50ns/ Div to 0.2 s/ Div in 21 calibrated steps ( 1-2-5) • Timebase A - X10 Mag: 5ns/ Div to 20ms/ Div • Timebase A – Accuracy: ± 3% ( ± 5% in X10 Mag) • Timebase A - Hold Off: Continuously adjustable to > 2X sweep time • Timebase B - Sweep Time: 50ns/ Div to 10µ s/ Div in 8 steps ( 1-2-5) • Timebase B – Accuracy: ± 3% • Timebase B - Delay Time: Continuously variable from 0.2µ s to 2s • Timebase B - Delay Modes: Continuous or triggered • Timebase B - Sweep Displays: A, B, A alt B, B triggered, X-Y X-Y Mode CH1-X axis, CH2-Y axis Sensitivity: Same as CH1 vertical amplifier Bandwidth ( X-axis) : DC to 2MHz Phase Error: £ 3° DC to 10kHz Triggering Trigger Modes: Auto, Normal, TV-V, TV-L Source: Int. CH2, line ext. Coupling: AC Slope: Positive or negative Trigger Sensitivity: • Int ( DC to 10MHz) : 0.5 Div • Int ( 10MHz to 100MHz) : 1.5 Div • Ext ( DC to 10MHz) : 200mV • Ext ( 10MHz to 100MHz) : 500mV • TV ( Int) : 1 Div Min • TV ( Ext) : 1V P-P External Trigger Input Impedance: 1MW + 20 pF Maximum Input Volts: 400V DC or AC peak Z Axis Modulation Sensitivity : ± 5V P-P Intensity increases with a negative going voltage input Bandwidth ( -3dB) : DC to 2MHz Input Impedance: Approx. 2 KW Calibrator Signal Voltage: 0.5V ± 3% P-P 1kHz Square Wave Duty Cycle: Approx. 50% CRT Type: 6 " rectangular CRT with internal graticule. ( 1 Div = 1cm) Acceleration Voltage: 12 kV General Specification Power Requirements: AC Input Voltage: 100V, 120V, 220V, 240V selectable Frequency: 50/ 60Hz Power Consumption: 55W Operating Temperature: 0 to 40° C at 35% to 85% relative humidity Dimensions: 5.25 " H × 12.67 " W × 14.5 " D Weight: 24 lbs. Supplied Accessories: Manual, 1 AC Power cord, ( 2) X10 Probes