Back to Top

Hi, Guest!

  LOKASI :  Kota Tangerang Selatan

Bergabung Selama :

BAGIKAN :   

Bagikan :

Oscilloscope Analog ATTEN AT7340

Update Terakhir
:
01 / 12 / 2019
Min. Pembelian
:
0
Dilihat Sebanyak
:
7 kali

Harga

CALL
Bagikan
:

Perhatian !

Perusahaan ini terdaftar sebagai Free Member. Hindari melakukan pembayaran sebelum bertemu penjual atau melihat barang secara langsung. COD (Cash On Delivery) atau bertemu langsung dengan penjual merupakan metode transaksi aman yang kami sarankan.

Detail Oscilloscope Analog ATTEN AT7340

ATTEN AT7340 Analog Oscilloscope Features : Dual channel - channel bandwidth: 40 MHz High Sensitivity 1Mv/ DIV 5mV/ div Sensitivity on Both Channels CH1 & CH2 Independent Channels CH1 Signal Output Two waveforms in different frequency can be observed via alternative trigger function High-speed sweep Algebraic Addition and Subtraction X-Y Operation 0.2¼ s/ div to 0.5s/ div Time Base( Uncal upto 20ns) Z Modulation TTL Level 8 x 10 cm Display Internal Graticule TV signal synchronous function, TV Triggering Frame ( V) & Line ( H) Line Trigger ALT Triggering AT7340 Model TECHNICAL SPECIFICATIONS VERTICAL AXIS Sensitivity: 5mV~ 5V/ DIV, 10 steps in 1-2-5 sequence ( X5 MAG: 1mV/ DIV) Sensitivity accuracy: d3% ( × 5MAG: d5% ) Vernier vertical sensitivity: continuously variable to 1/ 2.5 or less of panel-indicated value Frequency bandwidth: DC-20MHz ( × 5MAG: DC-7MHz) ; DC-40MHz ( × 5MAG: DC-15MHz) AC coupling: Low limit frequency 10Hz. ( With reference to 100KHz, 8DIV.Frequency response with-3dB) Rise time: Approx.17.5Ns ( × 5MAG: Approx.50Ns) / 9.5nS ( X5MAG: Approx.25nS) Input impedance: Approx. 1M ohm/ / Approx. 25pF Square wave characteristics Overshoot: d5% ( At 10Mv/ DIV range) other distortions and other ranges: 5% added to the above value DC balance shift: 5mV~ 5V/ DIV; ± 0.5 DIV, 1mV~ 2mV/ DIV± 2.0DIV Linearity: ? ± 0.1DIV of amplitude change when waveform of 2 DIV at graticule center is moved vertically. Vertical modes: CH1 single channel.; CH2 single channel DUAL: CH1 and CH2 are displayed ALT or CHOP selectable at any sweep rate. ADD: CH1+ CH2 algebraic addition Chopping repetition frequency: Approx.250KHz Input coupling: AC, GND , DC Maximum input voltage: 300V peak ( AC: frequency 1KHz or lower) When set probe switch at 1: 1, the maximum effective readout is 40Vp p( 14Vrms at sine wave) ; or set probe switch at 10: 1, the maximum effective readout is 400Vpp( 140Vrms at sine wave) Common mode rejection ratio: 50: 1 or better at 50KHz sinusoidal wave.( when sensitivities of CH1 and CH2 are set equally) Isolation between channels ( at 5Mv/ DIV range) : > 1000: 1 at 50 MHz; > 30: 1 at 20MHz; > 30: 1 at 40MHz CH1 signal output: At least 20Mv/ DIV into a 50 ohm termination, Bandwidth is 50Hz to at least 5MHz. CH2 INV BAL: Balanced point variation: d1DIV( Reference at center graticule) HORIZONTAL AXIS Sweep time: 0.2¼ Sec-0.5Sec/ DIV, 20Steps in 1-2-5sequence Sweep time accuracy: ± 3% Vernier sweep time control: d1/ 2.5 of panel-indicated value Sweep magnification: 10 times × 10MAG sweep time accuracy: ± 5% ( 20nsec-50nsec are uncalibrated) Linearity: ± 3% , × 10MAG: ± 5% ( 20ns and 50ns are uncalibrated) Position shift caused by× 10MAG: Within 2 DIV, at CRT screen center TRIGGERING Triggering source: CH1, CH2, LINE, EXT Coupling: AC: 20Hz to full bandwidth Slope: + / - Sensitivity: 20Hz-2MHz: 1.0 DIV, TRIG-ALT: 2DIV, EXT: 200Mv; 2MHz-20MHz: 1.5DIV; 20MHz or higher: 2.0DIV TRIG-ALT: 3DIV, EXT: 800mv TV: Sync pulse more than 1 DIV ( EXT: 1V) Triggering modes: AUTO; NORM; TV-V; TV-H. ( Both TV-V and TV-H synchronize only when the synchronizing signal is negative) Input impedance: Approx: 1M ohm/ / approx.25pF
Tampilkan Lebih Banyak